Author [NL] [FR] [ES] [DE] [SE] [IT] Safety recall wiring  (Read 1998 times)

0 Members and 1 Guest are viewing this topic.

  • Offline strathroy   ca

    • Trophy Pro  ‐    165
    • ***
    • Topic Author

    Offline strathroy

    • Trophy Pro
    • ***
    • Topic Author
    • Posts: 165
    • Bike: Trophy SE
    • City / Town: Strathroy
    • Country: ca
    Safety recall wiring
    on: Apr 18, 2020, 01.32 pm
    Apr 18, 2020, 01.32 pm
    On a American Facebook group there is a recall from Triumph listed for a rerouting of the ignition wires is this legit?
    MSTA MOtorcycle touring association

  • Offline Coconut   gb

    • Trophy God  ‐    10202
    • *****
      #1

    Offline Coconut

    • Trophy God
    • *****
    • Posts: 10202
    • Bike: 2017 Trophy SE
    • City / Town: South Birmingham
    • Country: gb
    Re: Safety recall wiring
    Reply #1 on: Apr 18, 2020, 01.47 pm
    Apr 18, 2020, 01.47 pm
    Yes it's genuine - There's a Long running Topic about this with all the information here :

    Ignition Switch Wiring WORLDWIDE Safety Recall SRAN574


  • Offline strathroy   ca

    • Trophy Pro  ‐    165
    • ***
    • Topic Author
    • #2

    Offline strathroy

    • Trophy Pro
    • ***
    • Topic Author
    • Posts: 165
    • Bike: Trophy SE
    • City / Town: Strathroy
    • Country: ca
    Re: Safety recall wiring
    Reply #2 on: Apr 18, 2020, 02.32 pm
    Apr 18, 2020, 02.32 pm
    Thanks I missed the thread. But that letter was sent in April 2020 to that person was this also related to the loom being too tight and pins being pulled out of a connector. So I should be going to the dealer? I've had all the recalls done but I don't remember this one being done. Do they just look and say yup or no

  • Offline Rick505   us

    • Trophy Pro  ‐    335
    • ***
      #3

    Offline Rick505

    • Trophy Pro
    • ***
    • Posts: 335
    • Bike: 2015 Trophy SE
    • City / Town: Albuquerque, NM
    • Country: us
    Re: Safety recall wiring
    Reply #3 on: Apr 18, 2020, 03.07 pm
    Apr 18, 2020, 03.07 pm
    *Originally Posted by strathroy [+]
    Thanks I missed the thread. But that letter was sent in April 2020 to that person was this also related to the loom being too tight and pins being pulled out of a connector. So I should be going to the dealer? I've had all the recalls done but I don't remember this one being done. Do they just look and say yup or no

    That's all I'm expecting.  I didn't take a close look at your original document/image you posted but there is a copy of the repair instructions available here with a couple of pages of repair instructions.

  • Offline Coconut   gb

    • Trophy God  ‐    10202
    • *****
      #4

    Offline Coconut

    • Trophy God
    • *****
    • Posts: 10202
    • Bike: 2017 Trophy SE
    • City / Town: South Birmingham
    • Country: gb
    Re: Safety recall wiring
    Reply #4 on: Apr 18, 2020, 03.09 pm
    Apr 18, 2020, 03.09 pm
    The Ignition wiring failures have been occurring since the Model was released in 2012,
    up to the end of production.  I commenced a campaign for Triumph and UK DVSA
    to address this problem in September 2019, which resulted in Triumph Safety Recall SRAN574
    commencing at the beginning of April 2020.

    The physical failure is usually where the wires are severed through at the base of the Ignition Switch.

    Less commonly the wires could be pulled out of their soldered connections
    at the base of the Ignition switch.

    ( There have been other reports of Handlebar switch wiring / pins being pulled out
    due to tight wiring that gets "stretched" when the handlebars are turned,
    that are not subject of this Safety Recall ).

    If you receive a Safety Recall letter then my advice is that you must have your Trophy inspected,
    and I would recommend having it inspected for this issue even if you don't receive the letter !

    May I suggest that it might be better for any further discussion to take place within the main Topic
    for this, as per the previous Link, so that any useful information is kept in one place ?

    Cheers  :821:



  • Offline Novocastrian   gb

    • Trophy Master  ‐    713
    • ****
      #5

    Offline Novocastrian

    • Trophy Master
    • ****
    • Posts: 713
    • Bike: TTSE
    • City / Town: Tynemouth
    • Country: gb
    Re: Safety recall wiring
    Reply #5 on: Apr 18, 2020, 04.48 pm
    Apr 18, 2020, 04.48 pm
    *Originally Posted by Coconut [+]
    I commenced a campaign for Triumph and UK DVSA
    to address this problem in September 2019, which resulted in Triumph Safety Recall SRAN574
    commencing at the beginning of April 2020.

    No Xmas card from Triumph to Coconut this year then  :745:
    Ken Hastie
    TTSE, a handful of BSAs, a Vespa 300 and an MGB

  • Offline Coconut   gb

    • Trophy God  ‐    10202
    • *****
      #6

    Offline Coconut

    • Trophy God
    • *****
    • Posts: 10202
    • Bike: 2017 Trophy SE
    • City / Town: South Birmingham
    • Country: gb
    Re: Safety recall wiring
    Reply #6 on: Apr 18, 2020, 04.53 pm
    Apr 18, 2020, 04.53 pm
    I won't lose any sleep over that - I don't really celebrate Christmas anyway,
    but if you look at it another way, just one or two "Law Suits" if they hadn't
    done anything to address the problem, could potentially have cost them MILLIONS !


  • Offline Trophy Moderator   gb

    • Forum Moderator
    • Trophy Pro  ‐    220
    • *****
      #7

    Offline Trophy Moderator

    • Forum Moderator
    • Trophy Pro
    • *****
    • Posts: 220
    • Country: gb
    Re: Safety recall wiring
    Reply #7 on: Apr 18, 2020, 05.20 pm
    Apr 18, 2020, 05.20 pm
    PLEASE NOTE :

    There is now a New Topic ( in the Lighting, Electrical and Wiring Section of the Forum )
    relating to the Safety Recall issued by Triumph for this problem,
    where continued discussions about this topic can be held :

    Ignition Switch Wiring WORLDWIDE Safety Recall SRAN574

    This Topic has now been Locked.

    Trophy Moderator