Author [NL] [FR] [ES] [DE] [SE] [IT] Topic: Engine management light  (Read 251 times)

0 Members and 1 Guest are viewing this topic.

  • Offline stnrsbrian

    • Trophy Junior  ‐    3
    • *
    • Topic Author

    Offline stnrsbrian

    • Trophy Junior
    • *
    • Topic Author
    • Posts: 3
    • Bike: Trophy se
    • City / Town: Plymouth
    Engine management light
    on: May 07, 2022, 10.53 am
    May 07, 2022, 10.53 am
     Hi all Iíve just replaced my battery ( the old was 7 years old ) now I have an engine management light on after starting  :763:

  • Offline Coconut   gb

    • Trophy God  ‐    9941
    • *****
      #1

    Offline Coconut

    • Trophy God
    • *****
    • Posts: 9941
    • Bike: 2017 Trophy SE
    • City / Town: South Birmingham
    • Country: gb
    Re: Engine management light
    Reply #1 on: May 07, 2022, 12.26 pm
    May 07, 2022, 12.26 pm
    It's not unusual for the Trophy to throw up an error code or two after Low Voltage.

    In particular "P1698" : "5 Volt sensor supply circuit malfunction" will often be logged.

    It's easy to check any Error codes that have been stored,
    and have them displayed on the Instrument Panel :

    Press the SCROLL UP and SELECT ( "i" ) buttons together,
    and hold them in while switching on the Ignition -
    Keep them held in until the Speedo and Tacho needles have completed their Sweep

    The screen should display "DTC" ( Diagnostic Trouble Codes )
    with any DTC's that have been stored listed underneath.
    If there are more than one, use the Scroll button to scroll through them.

    "P0000" is what you wart to see - it means there are NO DTC's stored.

    Make a note of any DTC's ( take a Photo ) and Switch the Ignition OFF when done.

    Refer to Reply #8 dated Mar 11, 2015 titled "Diagnostic Trouble Codes ( DTC's ) / Fault Codes" in this Topic :

    Servicing Data, Reference Info. & DTC ( Fault ) Codes
    for more information and a downloadable document listing all of the DTC's with their meanings,
    and further information such as how many "No Fault" starts are required before the "MIL"
    ( Malfunction Indicator Light / Engine Management Light ) is extinguished,
    and long they are held in Memory before being automatically cleared.

    Report back with any DTC's that you find if you need further advice  :028:

    Cheers  :821:


  • Offline stnrsbrian

    • Trophy Junior  ‐    3
    • *
    • Topic Author
    • #2

    Offline stnrsbrian

    • Trophy Junior
    • *
    • Topic Author
    • Posts: 3
    • Bike: Trophy se
    • City / Town: Plymouth
    Re: Engine management light
    Reply #2 on: May 08, 2022, 09.08 am
    May 08, 2022, 09.08 am
    Many thanks coconut  :763:

  • Offline pjhprop

    • Trophy Member  ‐    38
    • **
      #3

    Offline pjhprop

    • Trophy Member
    • **
    • Posts: 38
    • Bike: 2015 Trophy
    • City / Town: Leeds
    Re: Engine management light
    Reply #3 on: May 08, 2022, 09.24 am
    May 08, 2022, 09.24 am
    Had the same problem with battery failed at petrol station and wouldnt start. long story short the good people of Filey help me to start bike using spare battery and jump leads. Managed to get back home without issue engine management light on all the time. Fitted new battery fauly code P1698 showing. started several times and the engine management light is no more.

  • Offline Noggin   gb

    • Trophy Pro  ‐    108
    • ***
      #4

    Offline Noggin

    • Trophy Pro
    • ***
    • Posts: 108
    • Bike: 13 plate Trophy SE
    • City / Town: Southampton
    • Country: gb
    Re: Engine management light
    Reply #4 on: May 08, 2022, 12.36 pm
    May 08, 2022, 12.36 pm
    Or rather than wait use the excellent dealertool/tigertool soft ware and obd connector ( I mention both, because I can't remember which one i used recently when my battery died)
    Various bikes, then I grew up !
    1991 Triumph Trophy 1200
    2010 Triumph Sprint GT
    2013 Triumph Trophy 1215